Saturday, December 21, 2019
Figure Painting Total - November
After Valleycon, I found out that there were some Barnes and Noble exclusive sets for both Blitz Bowl and Space Marine Adventures. I had to order them to keep complete. I also got a 3D printed figure of Sam, from Trick R Treat. It is a bit rough looking but has already been basecoated, so finishing it up should not be too hard.
Blitz Bowl: Halflings - 6
Blitz Bowl: Undead - 7
Space Marine Adventures – Recon – 3
Space Marine Adventures – Rescue - 3
Sam (from Trick R Treat) - 1 – 3D printed – already painted (basecoated).
Nov total - figures bought 20, figures painted 0
Running total 2019 – figures bought 149, figures painted 1
Friday, December 13, 2019
Stairway!
At my wife’s work, each department is decorating there area in different themes for Christmas. Her department was originally going to do a Die Hard theme, but decided to change it to Home Alone theme instead. She said that I could make the staircase – five feet tall, out of cardboard.
I mean, of course I can. But I didn’t have enough large cardboard, so I asked if I could make it out of foam core, which she was okay with. The key requirements would be that it had to be at least 5 feet tall, and it had to be transportable.
I worked out the dimensions and told her it would cost about $20 - $40, which she was again okay with. I would not add a railing, would have very fiddly to make in sections, and have added another $10 - $40 depending on what I made the rails out of.
It had worked out to 12 sheets of 20” x 30” foam core, which I got at Dollarama for $1.50 each. I picked up 14 sheets, in case I needed more or messed up, so $21 for that. I ended up mis-cutting the second sheet I worked on the other side of the first set of stairs. I used a lot of the scraps for reinforcing seams and adding supports.
I picked up 2 rolls of wood grain flooring stickers, which I also got at Dollarama for $4 each, so another $8. I only used it on the stairs for the part that shows on the sides of the runner, so only ended up using a bit more than 1 sheet. I have plans for the rest of the second sheet.
I found 36” square pieces of red felt for the runner at Oomoomoo, a Japanese dollar store. They were $4 each and I picked up 4 of them. I only ended up using 3 of the squares but I bought the extra so as to not have to worry about matching the color if I needed more.
Using the plans, I cut out the sides of the base. I had to glue a second piece of the foam core behind the first three steps to give them the proper depth. These first three steps are normal size. The first two steps have a rise of 6 ¾” and the third has a rise of 6 ½”. This way the first three steps fits nicely on a single with of foam core. The steps have a run of 10 ½” which leaves a ½” overhang and allows these three steps to fit together on one length of foam core. The steps themselves are 20” wide, the same as the width of a sheet of foam core.
The upper piece is 30” deep, but 50” high. The upper section has 7 steps using forced perspective. The rise of the next three steps remains the same as the first three, but the next four on the next sheet are 6 ½” high. The steps get progressively smaller – 8 ½”, two at 6 ½”, 4 ½”, and the last three are all 2 ½” deep.
I cut out all the steps and risers. Using white wood glue, I glued the risers on first to allow some time for them to dry. I put some braces across the backs to help support the sides.
Then I cut the wood grain into 4 sections – 3 at 5” wide and the remaining one at 4.75” wide. I cut each piece an inch longer than the step it was going on so I could fold it over the exposed end. I put them on 4 ½” inches from the sides, again allowing overlap. The narrower ones I put on the left side of the steps as that would be against the wall.
I glued the steps on next, pinning through to the foam below to help hold it while drying. I later went in and taped all the steps from behind.
I switched to tacky glue and glued on the felt runner. I was careful to line up the pieces under the overhang of the lower steps, and at the back of the steps on the upper ones.
I then went back and used hot glue from the inside to tack the corners of the steps as well as to strengthen the supports. The finished stairs are 20” wide, 60” deep, and 70 1/8” tall.
It had worked out to 12 sheets of 20” x 30” foam core, which I got at Dollarama for $1.50 each. I picked up 14 sheets, in case I needed more or messed up, so $21 for that. I ended up mis-cutting the second sheet I worked on the other side of the first set of stairs. I used a lot of the scraps for reinforcing seams and adding supports.
I picked up 2 rolls of wood grain flooring stickers, which I also got at Dollarama for $4 each, so another $8. I only used it on the stairs for the part that shows on the sides of the runner, so only ended up using a bit more than 1 sheet. I have plans for the rest of the second sheet.
I found 36” square pieces of red felt for the runner at Oomoomoo, a Japanese dollar store. They were $4 each and I picked up 4 of them. I only ended up using 3 of the squares but I bought the extra so as to not have to worry about matching the color if I needed more.
Using the plans, I cut out the sides of the base. I had to glue a second piece of the foam core behind the first three steps to give them the proper depth. These first three steps are normal size. The first two steps have a rise of 6 ¾” and the third has a rise of 6 ½”. This way the first three steps fits nicely on a single with of foam core. The steps have a run of 10 ½” which leaves a ½” overhang and allows these three steps to fit together on one length of foam core. The steps themselves are 20” wide, the same as the width of a sheet of foam core.
The upper piece is 30” deep, but 50” high. The upper section has 7 steps using forced perspective. The rise of the next three steps remains the same as the first three, but the next four on the next sheet are 6 ½” high. The steps get progressively smaller – 8 ½”, two at 6 ½”, 4 ½”, and the last three are all 2 ½” deep.
I cut out all the steps and risers. Using white wood glue, I glued the risers on first to allow some time for them to dry. I put some braces across the backs to help support the sides.
Then I cut the wood grain into 4 sections – 3 at 5” wide and the remaining one at 4.75” wide. I cut each piece an inch longer than the step it was going on so I could fold it over the exposed end. I put them on 4 ½” inches from the sides, again allowing overlap. The narrower ones I put on the left side of the steps as that would be against the wall.
I glued the steps on next, pinning through to the foam below to help hold it while drying. I later went in and taped all the steps from behind.
I switched to tacky glue and glued on the felt runner. I was careful to line up the pieces under the overhang of the lower steps, and at the back of the steps on the upper ones.
I then went back and used hot glue from the inside to tack the corners of the steps as well as to strengthen the supports. The finished stairs are 20” wide, 60” deep, and 70 1/8” tall.
Subscribe to:
Posts (Atom)
